PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4” - 2”. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort.

Kit includes: (3/4” - 1 1/8”) Shaft diameter propeller puller, a wrench for the puller and prop nut, a stainless steel cotter pin, a brass prop shaft key, a brass nylock prop nut, waterproof grease, safety lanyard and is packaged in a rustproof carrying case. Clearence required between propeller hub and strut is 1/4” minimum.

PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4” - 2”. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort.

(3/4” - 1 1/8”) Shaft diameter tool only is the same propeller puller used in the PPF-101 Kit. Clearance required between propeller hub and strut is 1/4” minimum

PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4” - 2”. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort.

(1 1/4” - 1 1/2”) Shaft diameter propeller puller with removable handle and safety lanyard. Clearance required between propeller hub and strut is 5/8”.

PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4” - 2”. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort.

(1 5/8” - 2”) Shaft diameter propeller puller with removable handle and safety lanyard. Clearance required between propeller hub and strut is 3/4”.

PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4” - 3”. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it won’t slip off while in use.

PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4” - 3”. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it won’t slip off while in use.

PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4” - 3”. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it won’t slip off while in use.

PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4” - 3”. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it won’t slip off while in use.

PRO-PULL 10 Ton Chain propeller puller is designed to remove 2, 3, 4, 5 and 6 blade propellers on inboard shafts ranging from 1 1/4” - 2 1/2”. It’s made of high strength heat-treated allow steel and finished with cadmium for protection. The chains are grade 70 transport rated and are plated with cadmium. All bolts, nuts and threaded parts are either grade 5 or heat-treated allow steel finished with cadmium. Four propeller shaft adapters are used to set puller up for a specific shaft size and/or if propeller blades extend forward of the propeller hub. Four hooks with safety rings are used on propellers that have no clearance between the propeller hub and the strut. The chains conform to propeller blades that overlap to accomodate easy propeller removal without damage to the blades. Complete with zinc plated case hardened box wrench to operate puller a container of waterproof grease, waterproof tool box and instructions with diagrams for use.

PRO-PULL Outboard and Stern-Drive propeller puller is designed to remove any 2, 3, 4, 5 and 6 blade propeller. Structural components are made of heat-treated alloy steel finished with cadmium for protection. The bolt is grade 5 steel plated with cadmium. This puller will also remove any Duo-Prop. In addition this tool may also be used on many boats with inboard shafts up to 1 1/4” diameter. Comes complete with a waterproof carrying case for convenient stowage. This propeller puller requires no additional tools for operation.

PRO-PULL Outboard and Stern-Drive 6 in 1 propeller wrench is made of solid Nibral or Marine Grade Aluminum with six tools all in one easy to use handle. It will remove and install propeller nuts, cotter pins and propeller nut keepers on the following Outboard engines:

It will also work on all Stern-Drive engines made by: Mercury, OMC, Suzuki, Mariner, Yamaha and many others with either a 1 1/16” or 1 1/4” propeller nut. This tool comes packaged with a safety wrist strap to prevent toollose if accidentally dropped overboard.

PRO-PULL Versatile propeller puller is designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4” - 2.” It’s made of high strength heat-treated alloy steel and finished with cadmium for protection. The threaded rods, pivot pins and handle are manufactured using the finest stressproof steels available. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it can’t slip off while in use. The offset design of the pivot pins keep the hook of the tool on the propeller hub and pulls through the center of the propeller shaft. Minimal clearance between the propeller hub and strut are required due to the unique puller design. This propeller puller requires no addional tools for operation.